Fundamental Plumbing Insights for Installing a Bathtub
Fundamental Plumbing Insights for Installing a Bathtub
Blog Article
Just how do you feel when it comes to Installing A Bathtub?
Mounting a bath tub isn't specifically brain surgery, however it does require strong plumbing, woodworking, as well as often, tiling skills. Changing an old tub with a new one is also a reasonably challenging project. If the old bathtub is readily easily accessible, the project can relocate rapidly; if you have to open a wall surface to get rid of the old bathtub and position the new bathtub, the job is a lot harder. In either instance, the project is within a home handyman's skills, although you will need a helper to leave the old tub and set in the brand-new one. Make sure you have certified on your own for the work and are comfortable attempting it. As opposed to working with a professional to take control of a halfway-completed job, it is far better to take into consideration utilizing one prior to you start. Opportunities are you might need an expert plumber to make tube links.
This post will assist you install a new bath tub in your washroom if you have currently purchased a new tub and also do not require to alter the arrangement of your previous water supply pipes.
Your devices and also product list need to make up the following:
Planning for the Setup
To start with, the supporting structure supplied with the bath must be fitted (if called for) according to the producer's guidelines. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is important to see to it that if the faucet includes a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is likewise sensible to fit a supporting plate under the faucets device to avoid pressure on the bathtub.
Fit the versatile faucet connectors to the bottom of the two taps utilizing 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make certain you make use of all of the supplied washers.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final setting.
Removing Old Taps
If you need to change old taps with new ones as a part of your installment, then the first thing you need to do is disconnect the water. After doing so, turn on the taps to drain any kind of water remaining in the system. The procedure of removing the existing faucets can be fairly bothersome due to the restricted gain access to that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the taps. Have a cloth prepared for the continuing to be water that will originate from the pipes. When the supply pipelines have been gotten rid of, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning during this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Prior to proceeding to fit the new faucets, contrast the pipeline connections on the old taps to the new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the new taps to fit.
Installing the Tub
Using the two wood boards under its feet, place the bath tub in the needed placement. The wooden boards are useful in equally spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 tiny points.
The next objective is to make certain that the bathtub is leveled all round. This can be attained by checking the level and changing the feet on the tub till the level reads degree.
To install taps, fit all-time low of the furthest adaptable faucet port to the proper supply pipe by making a compression join; after that do the exact same for the other faucet.
Switch on the water system and examine all joints as well as brand-new pipework for leaks and also tighten them if needed. Fill the bath tub and additionally check the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, fix the bath paneling as defined in the producer's user's manual. Tiling and also sealing around the tub must wait till the bathtub has actually been made use of at the very least when as this will resolve it right into its final placement.
Suitable New Touches
If the tails of the new faucets are plastic, then you will require a plastic port to stop damage to the string. One end of the port fits on the plastic tail of the faucet and also the other end gives a connection to the existent supply pipes.
If you need to fit a monobloc, then you will need minimizing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the mounting opening in the bath/basin ensuring that the washers remain in area in between the tap and also the sink. Safeguard the faucet in place with the supplier supplied backnut. When the tap is firmly in position, the supply pipes can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal tap connectors. The previous type ought to be linked to the tap ends first, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to crack a rigid seal, causing the water to pass through the wall between the bathroom and the tiling, causing complications with dampness and possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to blend in your fixtures and also installations. They are sold in tubes as well as cartridges, as well as are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with twists of drenched paper or soft rope. Remember to always fill the bathtub with water prior to sealing, to enable the movement experienced when the bathtub remains in use. The sealant can crack relatively very early if you do not take into consideration this movement before securing.
Alternatively, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently offered on the marketplace. It is a good idea to fit the floor tiles using water-resistant or waterproof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like reading about Tools You Need to Install a New Bathtub ? Try leaving a remark down below. We will be interested to hear your views about this write up. We are looking forward to see you back again in the near future. Those who enjoyed reading our post please do not forget to share it. Thanks a bunch for your time. Come back soon.
Need quality service? Report this page